SmartPower DC Charger Test Feedback Aging System

Introduction:

• SP-DC charging pile test feedback aging system has the functions of GB-T standard interoperability specification testing and communication protocol consistency testing. It is mainly used for full load detection of DC charging piles and is an essential product for aging in production workshops.
  
  
• The GB-T standard meets the following test items: GB/T34657.1-2017 Electric Vehicle Conductive Charging Interoperability Test Specification Part 1 Power Supply Equipment; GB/T34658-2017 Electric Vehicle Non-onboard Conductive Charger and Battery Management System Communication Protocol Conformity Test; Built-in simulation vehicle BMS software GB/T27930-2015 Electric Vehicle Non-onboard Conductive Charger and Battery Management System Communication Protocol is compatible with the requirements of GB/T27930-2011 version; CCS1 and CCS2 standard communication protocol: charging communication meets ISO15118 and DIN70121 standards; power transmission meets IEC61851 standards; vehicle sockets meet IEC62196 standards; CHAdeMO  standard protocol meets CHAdeMO1.2&2.0 standards; vehicle sockets meet IEC62196 standards.
  

Features:

• The status of the charger's CHM, CRM, CTS, CML, CRO, CCS, CST, CSD, CEM and other messages are displayed in real time;  
  
• The vehicle-side message content and message cycle can all be set, and various car message conditions can be simulated;  
  
• The host computer uses the USB interface for direct control, which eliminates the cumbersome wiring and adapters compared to 485 and 232;  
  
• Real-time message output and translation during communication, and has real-time saving function. It is equivalent to having the function of a CAN box, which is convenient for direct use and fault analysis by various relevant personnel;  
  
• The average cycle, number of transmissions, maximum cycle, and minimum cycle statistics of various messages. The Gantt waveform output of the message makes the fault analysis of the charging pile more intuitive and comprehensive;  
  
• The communication consistency test of the charging pile has the function of outputting analysis reports;  
  
• With battery voltage simulation, it can simulate the battery positive connection, reverse connection, and no connection test;   
  
• Built-in K5, K6 switch state simulation function, multi-level R4 resistance setting, can test the critical gun drawing state, the complete gun drawing state, and the resistance adjustment range 295Ω~2550Ω;  
  
• Insulation module: can meet the insulation and reverse connection test and disconnection test of the charger, the test voltage access range is 0~1000V, and the insulation resistance adjustment range is 22.9kΩ~300kΩ;   
  
• It has a level 1 energy meter, which can display the output voltage, current, power, and charging power of the charging pile in real time, and can synchronize the data to the BCS message;   
  
• SOC increases automatically, and the charging time can be set to achieve the automatic aging test function; 
  
• Interoperability partial test, insulation fault test, gun removal test, battery reverse connection, disconnection test, etc.;   
  
• It has lead-out terminals such as pile end signal voltage, current, CC1, auxiliary power supply, abnormal synchronization signal, etc., which can be connected to other test instruments for pile end signal test and test inspection;    
  
• Internally integrated battery voltage simulator, voltage range 0-1000V, used for charging pile startup timing test (optional);    
  
• Charging pile socket: national standard, European standard, American standard, Japanese standard (optional);   
  
• Energy saving and environmental protection: high-efficiency operation in the full load range and ultra-low standby power consumption, effectively reducing energy loss and achieving energy saving and environmental protection;    
  
• Energy saving feedback: receiving load energy; can be fed back to the power grid, with a maximum conversion efficiency of more than 90%;    
  
• Feedback load function setting: current, power, time can be edited; leap, gradual change, hold, cycle can be set; 
  
• Cooling method: forced air cooling.   
  
• Optional metrological verification function: LAN, RS232, WIFI and other communication methods, built-in WIFI hotspot, remote wireless terminal. 0.05 level verification test items: working error, indication error, payment amount error, clock indication error, can complete the 0.05 level metrological verification test function of JJG1149-2018.
  

Specification:

Remarks: Special specifications can be customized according to customer requirements (Rated voltage, Rated power, Power supply voltage, box size etc).

Other Similar Products: